ZK-SJVA-4X 35W 4A Buck-Boost Converter with LCD Display (CC/CV)
ZK-SJVA-4X is a DC adjustable constant voltage constant current step down/up power supply module with LCD display. The LCD displays input voltage and output voltage, current, power and display status. The module is equipped with an adjustable stable output voltage and current. Set output current to meet the demand. It can be used as ordinary buck power supply module, charger and LED constant current driver.
Overview:
ZK-SJVA-4X is a DC adjustable constant voltage constant current step down/up power supply module with LCD display. The LCD displays input voltage and output voltage, current, power and display status. The module is equipped with an adjustable stable output voltage and current. Set output current to meet the demand. It can be used as ordinary buck power supply module, charger and LED constant current driver.
Features:
• High voltage resistant terminal.
• High quality acrylic shell.
• Supports complete disability output.
• Anti-reverse protection.
• Short circuit protection.
• Undervoltage protection.
• Anti-backflow Protection.
• Automatic buck/boost voltage.
• LCD screen HD display.
• Charging function.
• Select output.
• Display input voltage.
• Display output voltage, current, power.
• Working status indicator.
• Multiple parameters are displayed simultaneously.
• High current, low heat.
Specification:
• Product Name:ZK-SJVA-4X 4A Step Down/Up Power Supply Module with Display
• Working Voltage: DC 5.5V-30V
• Output Voltage: DC 0.5V-30V
• Output Current:4A(4A need heat sink;3A is stable for long time)
• Output Power:50W(50W need heat sink;35W is for 3A)
• Voltage Display Range:0~30V
• Voltage Display Precision:+/-0.5V
• Voltage Display Resolution:0.05V
• Current Display Range:0~4A
• Current Display Precision:+/-0.3A
• Voltage Display Resolution:0.005A
• Conversion efficiency: About 94%
• Working current:30mA
• Soft Starter: Yes(Failure at high power load)
• Anti-reverse Protection:Yes
• Anti-backflow Protection:Yes
• Short Protection:Yes
• Work frequency:180KHz
• Working Temperature range:-20℃~85℃
• Working Humidity range:0%-95%RH
• Size:66*48mm
Button/Potentiometer/LED introduction:
• Long press means need pressing button for more than 3 seconds.
• ON/OFF:Short Press to select output. Long press is used to restore default settings.
• IN/OUT:Short Press to switch display input voltage or output voltage. Long press is used to switch display output current or output power.
• CV Potentiometer: Adjust output voltage. Increase the output voltage when rotating clockwise.
• CC Potentiometer: Adjust output current. Increase the output current when rotating clockwise.
• ON LED: Green LED.Output indicator. It will turn ON when there is a output at output terminal.
• CC LED:Red LED.Constant current output indicator. It enters the constant current state when the load current reaches the set current and CC constant current indicator turns ON.
Instructions:
As a ordinary step down power module:
• Connect right input voltage at input terminal;
• Adjust CV constant voltage potentiometer to set output voltage
• Rotate CC potentiometer counterclockwise more than 10 turns at first.
• Test Output short circuit current by multimeter at 10A or 20A(Connect two Test Probes to output terminal on module)
• Rotate CC constant current potentiometer clockwise to set output current according to require overcurrent protection value.
• Test and using(E.g:Module's maximum output current is 2A if display 2A on multimeter. Red LED indicator will turn on if output reach to 2A.Otherwise LED is OFF.)
• The output voltage will decrease due to the current sampling resistor at the output. The higher the current, the more the voltage is reduced.
As a charger:
• Power module cannot be used as charger module if it does not support constant current function. If the voltage difference between the battery with insufficient voltage and the charger is very large will cause excessive charging and can also damage the battery. The module needs to be kept charging in constant current mode to reaching a certain level. Then automatically switch back to constant voltage charging.
• Make sure floating charge voltage and charge current for battery. If the lithium battery's parameter is 3.7V/2200mAh, then the float charge voltage is 4.2V, and the maximum charging current is 1C, which is 2200mA.
• Connect right input voltage at input terminal.(Note: Please don't connect load during set parameter).
• Test output voltage by multimeter and adjust CC potentiometer to make sure output voltage reach to require floating charge voltage.(If charge a 3.7V lithium battery, adjust the output voltage to 4.2V)
• Rotate CC potentiometer counterclockwise more than 10 turns at first.
• Test Output short circuit current by multimeter at 10A or 20A(Connect two Test Probes to output terminal on module)
• Rotate CC constant current potentiometer clockwise to set output current according to require charge current value.
• Connect battery at output terminal and start to charging.
As a high power LED constant current driver:
• Make sure LED working current and maximum working voltage.
• Connect right input voltage at input terminal.(Note:Please don't connect load during set parameter).
• Test output voltage by multimeter at output terminal and adjust CV potentiometer to set output voltage to LED's maximum working voltage.
• Rotate CC potentiometer counterclockwise more than 10 turns.
• Test Output short circuit current by multimeter at 10A or 20A(Connect two Test Probes to output terminal on module)
• Rotate CC constant current potentiometer clockwise to set output current according to require LED working current.
• Connect LED and test.
Note:
• Input undervoltage protection voltage is 4.7V.Module need re-power if input less than 4.7V.
• Please rotate the CV potentiometer counter clockwise more than 20 turns if there is no output voltage.
• It is a DC power module, So it cannot connect to AC power.
• Module need re-power after short protection.
• Please connect input before connect battery when use as charge and make sure output voltage is higher than battery voltage.
• 'IN-' and 'OUT-' cannot be connect together, otherwise module cannot support constant current output.
• Please make sure input power is more than load power.
• Please step down output power if module is hot.
• Please read use manual and description before use.
Application:
• Ordinary power supply
• Battery charger
• LED drive power
• Instrument voltage display
• Test meter
• Circuit test
• Power conversion
Package includes:
• 1 X ZK-SJVA-4X 4A Step Down/Up Power Supply Module with Display